thingiverse
AWACS Briefing Stick
Remixed model to accept ~10.5mm dowel for a briefing stick.
briefing 3D Models
12,352 resultsSponsored
thingiverse
grabcad
Military Briefing Tent
Briefing tent used by military for mission coordination
cults3d
bringing
The model itself is made in Zbrush 2020. Do not cut Not Hollow Files: OBJ, STL, FBX, ZT...
thingiverse
bridring
Customized version of http://www.thingiverse.com/thing:40704 Created with Customizer! h...
grabcad
MEETING AND BRIEFING HALLS
OBJ STL C4D 3DS
sketchfab
Dover Castle Briefing Model
No description provided.
SPONSORED
📈 Will the Fed cut interest rates in July?
Wall Street vs. the crowd. Who predicts the Fed correctly?
thingiverse
Bridging test
This is a simple bridging test. The distances are 20mm, 25mm, 30mm, 35mm, 40mm, 45mm, a...
prusaprinters
Bridging Test
prusaprinters
Bridging tests
Short Introduction VIDEO for the unofficial Drag Race.Are you needed to work on your br...
myminifactory
Grieving lady
This is a funerary sculpture from one of the graves of Margravine cemetery. The sculptu...
cults3d
Bringing Water
A girl holding water or milk buckets Polygons: 624,467
cults3d
Bridging Statue
Saw a video regarding the perfect bridging printing of the mushroom basket from @akakik...
prusaprinters
Bridging Test
Reinventing the wheel, yet again. The whole thing is 3 mm deep (z) and each strut is 1 ...
prusaprinters
Bridging Test
Bridges are 10mm, 20mm, 30mm, 40mm and 50mm
prusaprinters
Bridging Statue
Saw a video regarding the perfect bridging printing of the mushroom basket from @akakik...
prusaprinters
Bridging Test
With this model you can test 6 different distances:10mm20mm40mm60mm80mm100mm
thingiverse
Bridging Test
Customized version of http://www.thingiverse.com/thing:476845 Created with Customizer! ...
thingiverse
Bridging Test ()
Customized version of http://www.thingiverse.com/thing:476845 Created with Customizer! ...
prusaprinters
Grieving Angel
I found this model and knew I had to make it. Although it isn't meant for FDM printing ...
thingiverse
Extreme Bridging!
I wanted to know how far i could bridge. So i made an extreme test to test it.
thingiverse
Bridging Test
This is an FDM Bridging Test. Print with "Print thin walls" enabled in your slicer.
thingiverse
Bridging Test
This is a Bridge test for your 3d printer
thingiverse
bridging test
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/7R4...
cults3d
Bridging Test ()
Customized version of http://www.thingiverse.com/thing:476845 Created with Customizer!...
prusaprinters
bridging dice
A cube on which you can see how the printer bridges two columns without supports.I reco...
thingiverse
Bridging test
*THIS HAS IN AIR BRIDGING AT THE END OF THE PRINT!* It could fail, but you can test ...
thingiverse
Bridging Test
This small bridging test will confirm what your printer can do in just 20 minutes. It h...
thingiverse
Bridging Tower
Remix that trims to save filament and decrease the printing time and does not cut off t...
sketchfab
Grieving Man
Capture time: 15-20 min - 37 photos Device: Google Pixel 2 in portrait mode Processing ...
myminifactory
Bridging Statue
Saw a video regarding the perfect bridging printing of the mushroom basket from @akakik...
Sponsored
Sponsored